Wednesday, December 23, 2009

Georgia 2009 IECC Task Force to Meet on January 14, 2010

The following information is being reported by the Building Codes Assistance Project (BCAP).

The Georgia Department of Community Affairs (DCA) State Codes Advisory Committee (SCAC) 2009 IECC Task Force has posted the minutes from its meetings on November 16 and December 9. Its third meeting is scheduled for Thursday, January 14 at 10:00 a.m.(ET).

The task force will review the 2009 IECC and ASHRAE 90.1-2007 (the Georgia State Minimum Energy Code currently references the 2006 IECC and ASHRAE 90.1-2004), with a potential adoption expected in the spring of 2010. The task force will consist of stakeholders from state and local governments, utilities, homebuilders and other private industries. Upon approval by the SCAC and the DCA Board, this code will take effect on January 1, 2011.

Details

Tuesday, December 22, 2009

D.C. Seeks $35 Million from Department of Energy

Washington, D.C. mayor, Adrian Fenty, wants to assist D.C. property owners in making their homes and buildings more energy efficient.

The district has applied for a $35 million grant from the U.S. Department of Energy (DOE). It would use this grant to provide loans to homeowners and commercial property owners for energy-efficiency improvements. Under the program, these improvements would include solar panels or light fixtures and new storm windows and doors.

Fenty also hopes to sell approximately $250 million in bonds to keep the energy long fund going once the federal grant runs out.

Details

Friday, December 18, 2009

Title-24 Implementation Drawing Closer

On January 1, 2010 California will introduce the latest version of the Title-24 Building Efficiency Standards.

While it was originally scheduled to take effect in August 2009, delays in the compliance software pushed back enforcement of the new code until January 1, 2010.

The adoption of ASHRAE 62.2-2007 means that for the first time in California all low-rise residential buildings must provide whole house mechanical ventilation to address poor indoor air quality. This is caused by certain unanticipated side effects of improvements in the energy code.

Details

Wednesday, December 16, 2009

Green Building Promises Strong Growth

According to a report by McGraw-Hill, domestic green building will triple by 2013. This is expected to trigger $140 billion in construction spending. McGraw-Hill said growing public awareness, government regulations, and bottom-line advantages will help fuel this growth.

A substantial portion of this green building will be retrofits and renovations since many buildings are aging and inefficient.

Green building now comprises 5 percent to 9 percent of the market, but it could easily reach 30 percent ($15 billion in annual spending) within the next five years.

Details

Obama Calls for Home Improvements to Reduce Energy Consumption

On Tuesday, December 15, President Barack Obama spoke about the need for new federal incentives to make millions of homes more energy-efficient.

Obama said this would create jobs, save money for homeowners, and reduce pollution. Obama wants Congress to provide temporary incentives that encourage consumers to purchase items such as insulation, new windows and doors, and caulk to plug leaks.

Obama added that homes and offices are responsible for 40 percent of U.S. energy consumption and homes built in the first half of the last century may use 50 percent more energy than modern homes.

Details

Tuesday, December 15, 2009

NFRC Prepares to Launch CMA

The National Fenestration Rating Council's (NFRC) Component Modeling Approach (CMA) Product Certification Program is slated to be fully implemented on January 1, 2010.

CMA will establish whole-product energy performance ratings for nonresidential projects. NFRC plans to introduce CMA in California because it is one of the requirements for the state's updated Code of Regulations (Title 24), and across the country. CMA has undergone an extensive pilot program for the past several months. This gave NFRC time to train approved calculation entities (ACEs), manufacturer representatives who generate a product’s CMA label certificate, and IA’s that will approve components before they are available for use in a label certificate. It also enabled NFRC to accredit simulation labs.

NFRC also used the pilot program to test the component and to complete aspects of its software tool.

Details

Monday, December 14, 2009

NFRC Label Guarantees Accuracy

If you want to make your home more energy efficient, installing replacement windows is a good place to start.

Be sure to choose windows with the highest energy-efficiency rating. You can get glazed or unglazed windows. You can also choose between purchase windows with argon and krypton gas for more insulation.

Whichever product you choose, be sure it has a label from the National Fenestration Ratings Council (NFRC). This is your guarantee that the information on the window is accurate.

Details

Federal Tax Credit Provides Incentive for Replacing Fenestration Products

The energy bill extends tax credits for windows, doors, and skylights first established in the Energy Policy Act of 2005.

As of June 1, certain ENERGY STAR labeled windows, doors, and skylights qualify for a 30 percent tax credit, up to $1,500. ENERGY STAR’s Website explains that this program can help to reduce energy bills while improving comfort and protecting the environment. This federal tax credit is available through the end of 2010.

There are, however, some stipulations. All fenestration products must have a U-factor and a Solar Heat Gain Coefficient (SHGC) rating of 0.30 or below. These ratings need to be certified by the National Fenestration Rating Council (NFRC). NFRC is the only federally recognized organization for determining the energy performance of windows, doors and skylights.

Details

Friday, December 11, 2009

Codes Update Reported by BCAP

Below are some of the codes updates being reported by the Building Codes Assistance Project (BCAP)

Georgia

The Georgia Department of Community Affairs (DCA) State Codes Advisory Committee (SCAC) 2009 IECC Task Force meeting minutes from November 16 have been posted, as well as a presentation on the 2009 IECC. The amendments submitted through November 24 are also available. The Task Force met again on December 9.

The task force will review the 2009 IECC and ASHRAE 90.1-2007 (the Georgia State Minimum Energy Code currently references the 2006 IECC and ASHRAE 90.1-2004), with a potential adoption expected in the spring of 2010. The task force will consist of stakeholders from state and local governments, utilities, homebuilders and other private industries. Upon approval by the SCAC and the DCA Board, this code will take effect on January 1, 2011.

Georgia

The Georgia Residential Green Building Code Task Force has posted minutes from its September 30, November 3, and December 8 meetings. All proposed amendments to the National Green Building Standard, ICC 700-2008 need to be submitted to the Department of Community Affairs by December 15, 2009.
The Task Force has scheduled future meetings on January 20, February 18, March 16, April 6, and beyond. Check the Task Force's webpage for meeting announcements and details.

New Hampshire

The New Hampshire State Building Code Review Board has scheduled the completion of its work leftover from its November 13 meeting for an all-day meeting on Friday, December 11 to finish the adoption of potential amendments to the new state code to be based on the 2009 IECC (the current state code is based on the 2006 IECC). The effective date for the new code is now expected in April 2010.
Ohio

At its meeting on December 11, the Residential Code Advisory Council (RCAC) approved the creation of three-member Energy Subcommittee to address issues with the 2009 IECC. The RCAC stated an expected timeline for the new subcommittee to review the 2009 IECC and all similar options by the end of 2010. The RCAC would then make a recommendation in January 2011 to the Ohio Board of Building Standards (BBS). If approved by the BBS, the new residential code would take effect in 2012.
The first meeting of the Energy Subcommittee is scheduled to take place immediately after the next meeting of the RCAC on Wednesday, January 13.

Pennsylvania

On December 10, the Pennsylvania Independent Regulatory Review Commission (IRRC) approved a regulation adopting the 2009 IECC as the Commonwealth's new energy code for residential and commercial construction. It will be effective January 1, 2010.

As required by the Pennsylvania Construction Code Act of 1999 (and its amendments), the Pennsylvania Department of Labor and Industry (DLI) is required to update the state’s Uniform Construction Code (UCC) by December 31 of the year of the issuance of the new ICC family of codes (I-codes), including the IECC (the 2009 I-Codes were published in January 2009). The Uniform Construction Code Review and Advisory Council (Council) reviewed the 2009 IECC (the current UCC incorporates the 2006 IECC) this April and informed DLI that no provisions of the 2009 IECC are to be excluded.

DLI’s Regulation 12-89 adopting the 2009 I-Codes was submitted to the IRRC and legislative committees on October 23. The IRRC held a public meeting to consider approval of the regulation on December 10.

Tennessee

Having been charged to develop a new statewide residential energy code earlier this year, the Tennessee Fire Marshal’s Office has issued a rulemaking proposal adopting the 2006 IECC. The proposal would also mandate state buildings to use ASHRAE 90.1-2007 instead of Chapter 13 of the 2006 IBC. A hearing has been scheduled in Nashville for Wednesday, January 6 at 1:00pm CT, before which public comments will be accepted.

Upcoming Events & Comment Deadlines

Fri, Dec 11: New Hampshire – Scheduled meeting of State Building Code Review Board to adopt 2009 IECC

Mon, Dec 14: Montana – Comments on adoption of new energy code (2009 IECC) due to Codes Bureau

Mon, Dec 14: Virginia – Meeting of BHCD Codes and Standards Committee in Richmond, VA

Tues, Dec 15: Georgia – Proposed RGBC amendments to ICC-700 due to DCA

Tues, Dec 15: Georgia – Proposed amendments to 2009 IECC due to DCA SCAC

Wed, Dec 16: Georgia – RGBC Water/EE Work Group meets at DCA in Atlanta, GA

Sat, Dec 26: Washington, DC – 2008 DC Construction Codes become fully effective

Thur, Dec 31: Pennsylvania – 2009 Uniform Construction Code (2009 IECC) scheduled to take effect

Fri, Jan 1: California – 2008 Title 24 Standards effective statewide

Fri, Jan 1: Iowa – 2009 IECC effective statewide (with three-month grace period)

Wed, Jan 6: Tennessee – Comments on 2006 IECC due; meeting of Fire Marshal’s Office in Nashville

Wed, Jan 13: Ohio – RCAC meeting followed by Energy Subcommittee meeting

Mon, Jan 25: Virginia – Comments on 2009 IECC due to VA DCHD

Wed, Jan 27 – Fri, Jan 29: Green and Blue Conference in Auburn, AL

Mon, Feb 22 – Wed, Feb 24: RESNET 2010 Building Performance Conference in Raleigh, NC

Thur, Apr 1: New Hampshire – 2009 IECC scheduled to take effect

Details

Tuesday, December 8, 2009

Obama Favors Retrofitting Homes

In a speech earlier today, President Obama said retrofitting homes will help small businesses grow and create new jobs.

Speaking at the Brookings Institution, a Washington research institute, Obama talked about a new program that will provide rebates for consumers who make their homes more energy efficient through retrofitting.

Yesterday, Obama told a group of reporters that the country’s economic growth has moved into positive territory and added that the primary challenge now is to be sure job growth coincides with economic growth.


Details

Stimulus-Funded Weatherization Program in Indiana Looks Promising

Indiana’s stimulus-funded home weatherization program got off to a slow start, but now it's growing quickly and reaching its goal of improving energy efficiency in more than 8,000 homes by June 2010 looks promising.

The Indiana Housing and Community Development Authority reports that nearly 1,600 homes across Indiana have either undertaken or completed weatherization efforts. That’s 18 percent of the 8,661 the agency wants completed by May 30.

Details

Monday, December 7, 2009

NRFC -- Board of Directors Update

The National Fenestration Rating Council (NFRC) recently elected one member to serve on its Board of Directors and re-elected two others. Each will serve a three-year term, beginning this month.

An independent firm that managed the voting process reported the certified election results to the NFRC. Members of the NFRC:

• Elected Sneh Kumar, of TRACO, as a first-time Board member to fill a Fenestration Industry category seat.

• Re-elected Mike Thoman, of Architectural Testing, Inc., to a second term to fill a Laboratory category seat.

• Re-elected Kerry Haglund, of the Center for Sustainable Building Research, to a second term to fill a General Interest category seat.

"NFRC is proud that our members continue to demonstrate their dedication to the organization by participating in the Board election process," said Jim Benney, NFRC’s executive director. "We’re pleased to welcome a first-time Board member and to retain the services of two current Board members."

Additionally, NFRC announced its 2010 Board of Directors Executive Committee:

• Chair: Joe Hayden, Pella Corp.

• Vice Chair: Steve Strawn, Jeld-Wen, Inc.

• Treasurer: Kerry Haglund, Center for Sustainable Building Research

• Secretary: Steve Farrar, Guardian Industries Corp.

• Ombudsman: Jim Krahn, Marvin Windows & Doors

The Executive Committee will turn its attention to several priorities for 2010, including the successful deployment of the Component Modeling Approach (CMA) program and development of a fair, accurate, and credible rating program for fenestration attachments. In addition, the Executive Committee will focus on the roll-out of the Certified Insulating Glass Units (IGUs) requirement. In July 2010, IGUs used in NFRC-certified and -labeled products must be certified by a third-party Insulating Glass certification program prior to those products obtaining NFRC certification authorization.

Friday, December 4, 2009

Building Code Developments

Here are some of the code developments being reported by the Building Codes Assistance Project (BCAP)

Georgia

The Georgia Department of Community Affairs (DCA) State Codes Advisory Committee (SCAC) 2009 IECC Task Force meeting minutes from November 16 have been posted, as well as a presentation on the 2009 IECC. The amendments submitted through November 24 are also available. The Task Force will meet again on Wednesday, December 9 at 10 a.m. (ET) in Board Room 302 of the Department of Community Affairs, located at 60 Executive Park South, NE, Atlanta, GA 30329.

The task force will review the 2009 IECC and ASHRAE 90.1-2007 (the Georgia State Minimum Energy Code currently references the 2006 IECC and ASHRAE 90.1-2004), with a potential adoption expected in the spring of 2010.

Georgia

The Georgia Residential Green Building Code Task Force continues to meet next month. Work group meeting minutes and next scheduled meeting dates have been released. All work group meetings are open to the public:
· Administration – Next meeting: Dec. 8, 1:30pm (ET)
· Water and Energy Efficiency – Next meeting: Dec. 16, 9:30am (ET)
· Materials and Resources – Next meeting: Dec. 8, 1:30pm (ET)

The minutes from the Task Force's Nov. 3 meeting are now available. The Task Force will hold its third meeting on Tuesday, December 8 in the DCA Board Room located on the Third Floor of 60 Executive Park South, NE, Atlanta, GA 30329.

Hawaii

After the Hawaii Building Code Council approved the 2006 IECC with state-specific amendments on October 13, work has begun on the development of a statewide code to be based on the 2009 IECC. Minutes from the November 4 meeting of the 2009 IECC subcommittee of the Dept. of Business, Economic Development, and Tourism are available. The next meeting will be held on Tuesday, December 8 at 2:00pm HT (7:00 p.m. ET). A call-in number will be provided. The agenda will include:

1. Resolve the SHGC issue once and for all
2. Clear up language re allowing sealed attics with fiberglass and foam insulation in residences 3. Examine possible error regarding "maximum" vs. "minimum" emissivity and reflectivity in residential cool roof language
4. Settling on skylight SHGC
5. Assigning R-equivalent values to reflective roof and wall coatings
6. Amending the fenestration projection factor language to include a sliding scale for partially-shaded windows (see #1)
7. Incorporating exterior screen SHGC factors into #1, above
8. Examining the possibility of sub-zoning areas based on insulation levels or elevation.

Illinois

Legislation approved in August has directed the Illinois Capital Development Board (CDB) to adopt statewide the 2009 IECC for residential buildings and privately funded commercial buildings and ASHRAE 90.1-2007 for publicly funded commercial buildings. The legislation removed local home rule jurisdiction over energy codes and now includes residential and commercial buildings under the purview of the state code (currently, there is not a mandatory residential statewide energy code based on the IECC). A proposal is scheduled to go before the CDB at its regular monthly meeting on Tuesday, December 8.

New Hampshire

The New Hampshire State Building Code Review Board has scheduled the completion of its work leftover from its November 13 meeting for an all-day meeting on Friday, December 11 to finish the adoption of potential amendments to the new state code to be based on the 2009 IECC (the current state code is based on the 2006 IECC). The effective date for the new code is now expected in April 2010.

Ohio

A number of upcoming meetings of the Ohio energy code development community are scheduled for December:
Fri. December 4: The Codes Committee of the Ohio Board of Building Standards (BBS) will meet, but will not be reviewing a residential code proposal until January at the earliest.
Fri. December 11: The full BBS conference committee will meet (this is not a public hearing).

Pennsylvania

As required by the Pennsylvania Construction Code Act of 1999 (and its amendments), the Pennsylvania Department of Labor and Industry (DLI) is required to update the state’s Uniform Construction Code (UCC) by December 31 of the year of the issuance of the new ICC family of codes (I-codes), including the IECC (the 2009 I-Codes were published in January 2009). The Uniform Construction Code Review and Advisory Council (Council) reviewed the 2009 IECC (the current UCC incorporates the 2006 IECC) this April and informed DLI that no provisions of the 2009 IECC are to be excluded.

Virginia

In July, the Virginia Board of Housing and Community Development voted in favor adopting a recommendation to update the Uniform Statewide Building Code (USBC) to reference the 2009 IECC (it currently references the 2006 IECC). A comment period on the proposed USBC will be open from September 28, 2009 to January 25, 2010. The Board will review the comments received at its meeting in March 2010, with final adoption tentatively planned for late summer 2010. The next meeting of the Board’s Codes and Standards Committee will be Monday, December 14 at 10:00am ET.


Full Details

Thursday, December 3, 2009

Wausau Earns ACE Certification Through NFRC

Wausau Window and Wall Systems is among the first manufacturers to earn Approved Calculation Entity certification through the National Fenestration Ratings Council (NFRC). Accordingly, Wausau says it is now in a position to provide offer its customers reassurance to customers who want to fully understand new energy code requirements.

NFRC labels are currently mandated only in California and Washington, but nationwide adoption is likely.

According to Jessica Ferris, CMA’s Program Manager, ACE-certified users analyze performance data for non-residential fenestration energy ratings. By accessing NFRC's Component Modeling Approach software tool, CMAST, they are able to review libraries of approved frames, glass and spacer components.

These libraries help users configure fenestration products for a project, and allow them to obtain a U-factor, solar heat gain coefficient and visible transmittance rating for those products. Performance values are then compared to the energy requirements of local codes, such as California's Title 24, to determine compliance.

Wednesday, December 2, 2009

NFRC's Board of Directors -- Three Seats Filled, Opportunities Remain

NFRC’s Board of Directors – Three Seats Filled but Opportunities Remain

NFRC extends a special thank you to all of its voting members who participated in November’s online board election. The election is completed and the results are in.

Results

Sneh Kumar of TRACO was elected as a first-time Board member to fill the Fenestration Industry Category seat.

Mike Thoman of Architectural Testing, Inc. was re-elected to a second term to fill the Laboratory seat.

Kerry Haglund of the Center for Sustainable Building Research was also re-elected to a second term, filling the General Interest seat.

Remaining Opportunities

Longtime NFRC advocate, Board Member, and Certification Policy Committee (CPC) Chair, Roland Temple has chosen to retire, and his departure leaves two leadership voids – a General Interest Category Board Seat and the CPC Chair.

Accordingly, the Board of Directors is asking NFRC members to help fill these two seats. The General Interest Board seat will re-open for general election next fall, but still needs to be filled on an interim basis.

Individuals serving in the General Interest Category must be employed by or have a significant affiliation with current NFRC members in good standing who are in the General Interest membership category.

The CPC Chair is selected from among NFRC membership and holds an ex-officio (non-voting) seat on the NFRC Board of Directors. The seat also includes a number of other fiduciary responsibilities accorded to that position. NFRC will provide detailed information to anyone who is interested.

If you would like to recommend someone to fill the General Interest Board Seat or the CPC Chair, please contact Jim Benney, NFRC’s Executive Director, at
jbenney@nfrc.org.

Please submit your recommendations by December 15, 2009.

Monday, November 30, 2009

NFRC Accredits Lab Outside U.S.

NFRC has accredited its first laboratory outside North America

The laboratory is in Brummeria, Pretoria, South Africa, and it was accredited for thermal testing. The name of the laboratory is simply, Thermal Test Laboratory. It is managed by Gerrit Genis.

The on-site inspection occurred in July of 2009 by Bipin Shah.

Wednesday, November 25, 2009

Codes Updates from around the United States

These are some of the latest codes updates being reported by the Building Codes Assistance Project (BCAP).

Georgia

The Georgia Department of Community Affairs (DCA) State Codes Advisory Committee (SCAC) 2009 IECC Task Force began meeting on November 16. The task force will review the 2009 IECC and ASHRAE 90.1-2007 with a potential adoption expected in the spring of 2010.

Montana

On June 25, the Montana Building Code Council voted to adopt the 2009 IECC with amendments. A public hearing on the new energy code, during which comments may be submitted, is scheduled for Monday, November 30.

New Hampshire

The New Hampshire State Building Code Review Board has scheduled the completion of its work leftover from its November 13 meeting for an all-day meeting on Friday, December 11 to finish the adoption of potential amendments to the new state code to be based on the 2009 IECC

Ohio

A number of upcoming meetings of the Ohio energy code development community are scheduled for December:

Friday. December 4: The Codes Committee of the Ohio Board of Building Standards (BBS) will meet, but will not be reviewing a residential code proposal until January at the earliest.

Tuesday. December 8: Deadline for public comments on the Ohio Residential Codes Advisory Committee (RCAC) proposal to update the Residential Code of Ohio for One-, Two-, and Three-Family Dwellings (RCO), which is based on the 2009 IECC with several weakening amendments.
Wednesday. December 9: The RCAC will meet to debate and hear testimony on the RCO proposal.

Friday. December 11: The full BBS conference committee will meet (this is not a public hearing).

Pennsylvania

As required by the Pennsylvania Construction Code Act of 1999 (and its amendments), the Pennsylvania Department of Labor and Industry (DLI) is required to update the state’s Uniform Construction Code (UCC) by December 31 of the year of the issuance of the new ICC family of codes (I-codes).

Virginia

In July, the Virginia Board of Housing and Community Development voted in favor of adopting a recommendation to update the Uniform Statewide Building Code (USBC) to reference the 2009 IECC (it currently references the 2006 IECC). A comment period on the proposed USBC will be open from September 28, 2009 to January 25, 2010. The Board will review the comments received at its meeting in March 2010, with final adoption tentatively planned for late summer 2010.

Full Details

NFRC Exhibits at 15th Annual Win-Door Show, Canada Codes Work Nears End

NFRC hosted an exhibit booth at the 15th annual Win-Door North America Show, which was held November 17-19 at the Metro Toronto Convention Centre.

The show featured several educational sessions to update attendees on code developments. One session pointed out that the Canada national building code for 2010 is drawing toward a conclusion. The 2010 code, however, must be adopted by Canada’s various provinces and will therefore likely go into effect during 2011.

Full Details

Tuesday, November 24, 2009

Fenestration Industry Veteran, Roland Temple, Retires

As reported at the recent NFRC Fall Meeting in San Antonio, Roland Temple has retired.

Roland was a long-time NFRC advocate, Board Member, and Certification Policy Committee (CPC) Chair; and his guidance will be sorely missed.

His departure leaves two leadership voids; namely a General Interest Category Board Seat and the CPC Chair.

Friday, November 20, 2009

The Fall Meeting Is in the Books

That will do it from beautiful San Antonio. We'll see you all again next April in New Orleans.
In the meantime, be sure to check NFRC News Now at least once a day - we've gone 24/7, and this is the best place to get information about NFRC and the fenestration energy performance business!

Closing Thoughts from the Chair

Well, the 2009 Fall Membership Meeting has now come to a close, and as always I find myself amazed and appreciative of all the hard work and dedication put forth by everyone involved. As usual, many of the debates over the past week were very spirited. I know that in some ways this can be a source of frustration, but as I’ve stated in the past I take this as a sign of a truly healthy and vibrant organization in which everyone is genuinely committed to “getting it right.” If we didn’t really care about what we’re doing, these debates would be far less passionate, but where’s the fun in that? So, I again extend my appreciation and congratulations to the hardest working and most dedicated people I know … the members and staff of NFRC.

Following are specific thoughts on the past week, in no particular order:

· Clearly the major topic of interest this week was advancement on rating procedures for attachments. It’s obvious we have much more work to do, and in particular the issue of appropriate reference products needs to be settled. However, despite the challenges we faced this week, I believe we continue to make excellent progress at a rather remarkable pace.

· IG certification is also a topic of great interest as the July 1, 2010, date approaches. I want everyone to know that the Board is hearing all the comments and concerns being offered, and the Board will give each item its due consideration. However everyone also needs to know that at this time, the July 1, 2010, date is unchanged, and all participant are strongly encouraged to continue marching toward that date.

· Completion of the 901 AEP procedure is truly an historic milestone in our history and evolution. This effort has been underway for as long as I can recall. Granted we have not yet achieved the ultimate goal of a consumer-friendly AEP rating, but the approval of the revised 901 is a major step in reaching that goal.

· The CMA Program continues to make advancements. The current pilot program is providing us valuable information for final adjustments as we move into the full program in early 2010.

· I very definitely have mixed feelings about bidding farewell to Roland Temple. In one sense I’m very happy for him and wish him all the best as he enters into retirement. On the other hand, I really wonder if NFRC will ever be the same without him. Roland, you are truly one of the unique, even special, individuals who helped NFRC become the success that it is today and will be in the future. You will be sorely missed and leave behind shoes (actually boots) that are simply too big to ever fill. Best wishes to you and Neville as you enjoy your retirement. Thanks for all you’ve done, and God Bless !!!

· Lastly, I hope everyone enjoyed all the 20-year celebration festivities. Since the Thursday morning Board meeting ran a little long, we didn’t get a chance to review everyone’s responses to my “homework” assignment about sharing their favorite memories over NFRC’s first 20 years. So, here they are:

o The Alaska Board meeting that got “moosed."
o In 1992 we had 400 people in New Orleans as the first label requirements were pending. At that point we knew NFRC would work and last!
o The dinner during the Miami meeting. Great food, drink, entertainment – and cigars.
o The rotating bar at the hotel in Arlington, VA.
o The music and beautiful people and scenery in Quebec City.
o Meeting in Berkeley, CA when manufacturers threatened to lynch Nehemiah.
o Forming the NGRC – the National Gumbo Rating Council.
o The sunsets in Hawaii.
o Nehemiah, John Hogan, and Gary Curtis keeping us on our toes.
o The all you can eat snack shack in Tempe, Arizona.
o Sailing trip with whales in Hawaii (Big Island).

As you can see, most of these memories are tied into the places where we meet. Here’s hoping that many of you made new favorite memories here in San Antonio.

I look forward to seeing you all again in New Orleans next Spring. Until then, and as always … THANKS FOR ALL YOU DO !!! (And also, Happy Holidays!)

Thursday, November 19, 2009

Board Applauds Roland Temple's Service

At the end of the Board of Directors meeting, Chair Joe Hayden announced that NFRC Board Member Roland Temple of AZS Consulting is retiring. Hayden thanked Temple, the winner of NFRC's first NFRC Member of the Year award in 2008, for his years of dedication and service to NFRC and lamented that he can’t be replaced.

Roland asked us to share his favorite NFRC memory with everyone:

To All –

It has been a great blessing and pleasure in my life to have spent 20 years with NFRC. I know that I have not been associated with all of you for that long but “you all” are a part of my NFRC history. My prayers and best wishes are for your continued success. I love you all and will miss you. It is a difficult thing to pick one “adventure” as a favorite memory. However I still think that stepping out on our own was the best “adventure” of my NFRC involvement. As a result of this we have a great management team/staff. Keep up the good work.

God Bless You,
Roland

Good luck, Roland!

Board Hears Details of Virtual Membership Meeting

During the Board meeting, Cheryl Gendron, NFRC’s meetings manager, presented information on NFRC’s first “virtual” meeting, planned for July 19-22, 2010. The online meeting will take the place of the usual in-person Summer Membership Meeting.

The meeting will be conducted as a webinar, which can accommodate up to 1,000 participants. Business will be limited to committee and subcommittee sessions. There will be no task group meetings.

“Staff will be extensively testing this new process,” Gendron told the Board. “There will be a dry run a few weeks before the meeting with staff and a handful of registrants.”

This will be the first time that NFRC will conduct an online membership meeting. Gendron invited feedback on the process and encouraged anyone who’s attended online meetings to share their thoughts.

Look for more information on the Summer 2010 VIRTUAL Committee Week on the NFRC's meetings Web page.

Board of Directors Passes Motions


The last day of the NFRC 2009 Fall Membership Meeting concluded with the Board of Directors meeting this morning. After hearing reports from the Accreditation Policy, Technical Interpretation, and Certification Policy Committees, the Board turned its attention to motions presented by several other committees.

The Research and Technology Committee, chaired by Werner Lichtenberger of TruSeal Technologies, Inc., brought forward several action items. Among the actions, the Board approved motions to:

-Extend the Window 6/THERM 6 Validation Research project to the NFRC Spring 2010 Membership Meeting.
-Extend the Condensation Resistance for CMA Research project deadline until January 31, 2010.

Then, the Board passed additional motions under the Research and Technology Committee, including ones to:

-Approve NFRC 101 as amended with implementation upon publication
-Reaffirm the NFRC 103 document as a 2010 document with implementation upon publication (January 1, 2010).

Lichtenberger also reported that the Optical Properties Subcommittee is developing an NFRC 302 ballot for the NFRC 2010 Spring Membership Meeting. Major optical property submission process changes are being considered.

Nils Petermann of the Alliance of Save Energy reported that the Regulatory Affairs and Marketing committee dropped the legislative update from Monday’s session due to time constraints, but it will be posted to the NFRC Web site.

The Board then turned its attention to the Technical Committee. Among the motions it passed, the Board:

-Reaffirmed NFRC 400-2004 as NFRC 400-2010, with implementation on January 1, 2010.
-Approved the NFRC 100 Applied Films ballot document, with implementation on January 1, 2010.
-Approved the NFRC 100 Dynamic Attachment for Swinging Door (DASD) ballot
-Reaffirmed NFRC 200-2004 as NFRC 200-2010 for approval with implementation upon publication, and sunset 200-2004 at the same time.
-Approved the NFRC 901-2010 ballot and sunset the existing 2004 document at the same time (to be implemented upon publication).

NFRC Board Chair Joe Hayden described passage of the last motion as “an historic moment.”

The Board then took action on Ratings Committee business presented by JELD-WEN’s Steve Strawn, chair of the committee. Among the motions it passed, the Board approved:

-The NFRC 700 Applied Film ballot upon which may be used upon publication and mandatory on July 1, 2010. (This motion featured an amendment to add “without film” values to each of the performance rating columns).
-That the metric labeling requirement be allowed to 2 decimal places immediately and recommend that the NFRC 700 be revised to allow those requirements and to direct the metric labeling working group (chaired by J. Baker) to develop a recommendation as soon as possible and to bring that recommendation directly to the Board for final action.
-The NFRC 700-2010 Applied Films ballot, with implementation upon publication.
-The NFRC 705-2010 ballot with implementation upon publication.

The Board also approved an implementation plan for 2010 procedure.

After that action, Strawn presented the results of the Ratings Committee’s straw poll from yesterday. The Board approved a motion to the new product guidelines that the new product ratings and labeling plans be part of the new product guidelines document and these plans be approved by the BOD prior to Technical Committee or Ratings Committee work.

Good morning!

Welcome back to NFRC News Now's coverage of the NFRC Fall Membership Meeting. The Board of Directors meeting is underway, so check back throughout the day for updates.

Wednesday, November 18, 2009

Good night!

The third day of business at the NFRC Fall Membership Meeting is complete. NFRC News Now is signing off for the evening - coverage will continue tomorrow morning. Have a good night!

Ratings Committee Advances Numerous Items to Board

The Ratings Committee wrapped up the day’s proceedings by moving numerous ballots to the Board of Directors, holding a lengthy debate on an implementation plan for 2010 documents, and conducting an informal straw poll.

After Steve Strawn of JELD-WEN opened the meeting, John McFee of WDMA, and chair of the Labeling Subcommittee, brought forward two action items on behalf of his subcommittee:

-A motion to move NFRC 700 Applied Film Ballot to the Board of Directors for approval upon which may be used upon publication and mandatory on July 1, 2010.
-A motion that the metric labeling requirements be allowed to two (2) decimal places and recommend that the NFRC 700 be revised to allow the requirements. Direct the working group to develop a recommendation as soon as possible and to bring that recommendation directly to the Board for final action.

The Ratings Committee passed both motions. The latter issue is on a fast track due to upcoming requirements in Canada.

The Certification Subcommittee, chaired by Joe Jonely of Amsco Windows, then presented five motions to the Ratings Committee, all of which passed:

-Move the NFRC 700-2010 Applied Films Ballot to the Board of Directors for approval and to be implemented upon publication.
-Move the NFRC 700-2010 Lineal Supplier Ballot to the Board of Directors for approval and to be implemented upon publication.
-Move the NFRC 700-2010 Thermo-Physical Ballot to the Board of Directors for approval and to be implemented upon publication.
-Move the NFRC 700-2010 Private Labeler Ballot to the Board of Directors for approval and to be implemented upon publication.
-Move to establish a mandatory date of April 1, 2010, requiring highlighting or circling the correct performance value on the door label as listed in NFRC 700 Figure B-2.

Gary Curtis of ECOS Consulting, who is co-chair of the Component Modeling Approach (CMA) Ratings Subcommittee, presented one action item from his subcommittee. The Ratings Committee considered and approved the subcommittee’s motion to approve the NFRC 705-2010 Ballot and forward it to the Board of Directors for approval with implementation upon publication.

Thoman Presents 2010 Procedures Plan
The agenda then turned to new business. NFRC Board Member Mike Thoman of Architectural Testing presented a recommended implementation plan for 2010 procedures. After a long debate, the Ratings Committee passed a motion to approve the following implementation plan for 2010 procedures.

Any existing certification shall be allowed to exist for the remainder of the existing certification life.

1) Certification of new products and recertification of existing products may use the 2004 ratings under the following conditions:

a) Testing and simulations shall be completed using 2004 procedures no later than 1/31/2010; and
b) The reports for testing and simulation using the 2004 procedures shall be submitted to an IA in their entirety no later than 2/28/2010; and
c) The IA may issue 2004 CARs through 6/30/2010.

2) Certification of new products and recertification of existing products may use the 2010 ratings starting 1/1/2010

3) Additions and revisions of existing certification shall be performed using the procedure of the original certification.

4) A product tested in accordance to 102-2004 prior to 2/1/2010 may be used as a validation test in conjunction with an NFRC 100 -2010 simulation until four years after the date of the thermal test.

This plan now moves to the Board of Directors for approval.

Ratings Committee Conducts Informal Poll
Strawn concluded the Ratings Committee meeting by conducting an informal straw poll on three questions:

1) To allow (encourage) that ratings and labeling plans be approved prior to technical committee work when starting on rating new products.

Straw poll result: 19 agree, 4 disagree

2) Allow sash kits in pocket windows to be considered as attachment products.

Straw poll result: 10 agree, 8 disagree

3) Allow optional bulk labeling of windows, doors, and skylights. Bulk packagers up to 20 individual like products would qualify for one bulk label.

Straw poll result: 9 agree, 8 disagree

(This article was updated on 11/19/09.)

CMA Ratings SC Moves NFRC 705 Ballot Forward

The CMA Ratings Subcommittee held what likely was its shortest meeting ever. After Co-chair Mike Manteghi of TRACO opened the subcommittee meeting, Sneh Kumar, also of TRACO, reported on the activities of the CMA Complex Products Task Group.

Kumar noted that earlier this afternoon the CMA Technical Subcommittee had passed a motion to delay the development of complex products ratings. This means that the task group now has to figure out what to do, he explained.

NFRC Chair Joe Hayden then reiterated that the negative comment from Pella/EFCO that called for shelving the ballot for a year did so because the ballot referred to all attachment products. However, he said that the negative comment did not mean to discourage individual complex products from coming forward in that period.

The subcommittee then proceeded to act on the NFRC 705-2010 Ballot. After the subcommittee found the single comment on the NFRC 705-2010 ballot to be editorial and persuasive, it passed a motion to approve the NFRC 705 -2010 Ballot and forward it to the Ratings Committee for approval with implementation upon publication.

Labeling Subcommittee Passes Two Motions

The Labeling Subcommittee, chaired by John McFee of the Window & Door Manufacturers Association (WDMA), took action on two motions this afternoon.

Before it did so, the subcommittee heard reports from task groups. Charlie Curcija of CARLI, Inc., reported that the CMA Label Task Group doesn’t have any further work. “We developed a label, we finished a label, it is being used,” he said. McFee said that even though the task group has been suspended, any action items that come through in the future will be directed to it.

Mike Cienian of Hunter Douglas, chair of the Attachment Label Task Group, reported on its activities, and read a statement from Co-Chair Thomas Morrissey. The task group’s first official conference call will be held in mid-December, and Morrissey, also of Hunter Douglas, has drafted a proposed scope statement that Cienian shared with the subcommittee.

The subcommittee then passed a motion that metric labeling requirements be allowed to two (2) decimal places and that the NFRC 700 be revised to allow the requirements. The motion also directs the working group to develop a recommendation as soon as possible and to bring that recommendation directly to the Board for final action.

Business then turned to the NFRC 700-2010 Applied Films Ballot. After all negative comments were withdrawn, the subcommittee passed a motion to move the ballot to the Ratings Committee for approval and implementation upon publication.

Sponsor Spotlight: PAMA

The Professional Awnings Manufacturers Association (PAMA) is the silver-level sponsor of the NFRC 2009 Fall Membership Meeting. With more than 300 manufacturing members, PAMA is the only international trade association that supports the awning industry.

This afternoon NFRC News Now spoke with John Gant, of Glen Raven, Inc., who serves on PAMA’s Board of Directors and is a member of NFRC. He is actively involved in about a half dozen attachment task groups.

In early 2008, PAMA joined NFRC, before the Spring Membership Meeting in Nashville. “Glen Raven and PAMA joined to pursue energy ratings for window awnings,” explained Gant.

PAMA has sponsored NFRC meetings because it’s a good opportunity to get its name and mission in front of the NFRC membership, said Gant.

He noted that awnings fell out of favor in the 1960s as air conditioning became common in the United States, but these products are making a comeback. They become a lot of more popular especially when energy prices rise, he explained.

The green building movement is drawing attention to attachment products as well, said Gant. He explained that green building and energy efficiency programs should have technical information on the energy performance of attachment products.

Gant said that other manufacturers are interested in developing attachment ratings and are getting involved in the NFRC process. “There is broad industry support for this work.”

Certification SC Moves Four Ballots

The Certification Subcommittee, chaired by Joe Jonely of Amsco Windows, moved four ballots forward to the Ratings Committee, including the:

  • NFRC 700-2010 Private Labeler Ballot

  • NFRC 700-2010 Thermo-Physical Ballot, but only after vigorous discussion of a negative, submitted and withdrawn by Jim Krahn of Marvin Windows & Doors regarding Appendix B of NFRC 101


  • NFRC 700-2010 Applied Films (U-Factor) Ballot

  • NFRC 700-2010 Lineal Supplier Ballot


The subcommittee concluded its business by passing a motion that the Certification Subcommittee establish a mandatory date of April 1, 2010, requiring the highlighting of the door matrix label as listed in the NFRC 700 Figure B.2.

Technical Committee Moves 11 Ballots

Wrapping up an extended Technical Committee Block that spanned two days and 10 hours, the Technical Committee - under the leadership of Vice Chair Steve Johnson of Andersen Corporation - passed 11 motions on to the NFRC Board of Directors for review and approval. These motions included:

From the AEP Subcommittee, to approve changes to NFRC 901-2004, to move it to the Board of Directors for approval as NFRC 901-2010 to be implemented upon publication, and to sunset NFRC 901-2004.

From the Air Leakage Subcommittee, to reaffirm NFRC 400-2004 as NFRC 400-2010 and to forward it to the Board of Directors for approval and implementation on 1/1/2010.

From the U-factor Subcommittee, to approve the NFRC 100 Applied Films Ballot and to forward it to the Board of Directors for approval and implementation on 1/1/2010.

From the U-factor Subcommittee, to approve NFRC 102-2010 and to forward it to the Board of Directors for approval and implementation on 1/1/2010.

From the U-factor Subcommittee, to approve the NFRC 100-DASD Ballot and to forward it to the Board of Directors for approval and publication into the NFRC 100-2004 and NFRC 100-2010 documents, with implementation of the revised NFRC 100-2004 immediately upon publication and implementation of NFRC 100-2010 on 1/1/2010.

From the U-factor Subcommittee, to approve NFRC 100-2010, the NFRC 100 Garage-Rolling Door Ballot, and the NFRC 100 Validation Matrix Ballot and to forward them to the Board of Directors for approval and implementation on 1/1/2010.

From the SHGC Subcommittee, to reaffirm NFRC 200-2004, with approved changes, as NFRC 200-2010, to forward it to the Board of Directors for approval and implementation upon publication, and to sunset NFRC 200-2004 at same time.

From the SHGC Subcommittee, to reaffirm NFRC 201-2004, with approved changes, as NFRC 201-2010, to forward it to the Board of Directors for approval and implementation upon publication, and to sunset NFRC 201-2004 at same time.

From the SHGC Subcommittee, to approve the NFRC 200 Applied Films Ballot, to forward it to the Board of Directors for approval and insertion into NFRC 200-2010 and implementation upon publication.

From the SHGC Subcommittee, to approve NFRC 200 DASD, to forward it to the Board of Directors for approval into the NFRC 200-2004 and NFRC 200-2010 documents and implementation upon publication.

From the CMA Subcommittee (Technical), to approve the NFRC 100 Section 5.9 Ballot and forward it to the NFRC Board of Directors for approval and implementation upon publication with the entire 2010 documents.

Proposed Implementation Plan and New Task Group
Mike Thoman offered an implementation plan for all the new 2010 documents, and agreed to bring it forward for formal review and approval during the Ratings Committee block on Wednesday afternoon.

The committee also formed a TDD Testing Task Group under the SHGC Subcommittee.

CMA Tech SC Advances NFRC 100 Sec. 5.9

Among its business this morning, the Component Modeling Approach (CMA) Technical Subcommittee advanced NFRC 100 Section 5.9 and delayed development of a rating procedure for complex products.

TRACO’s Mike Manteghi, chair of the CMA Technical Subcommittee, opened the meeting, followed by a report from the subcommittee’s CMA Technical Task Group.

Sneh Kumar of TRACO gave an update on behalf of the task group noting that it had balloted NFRC 100 Section 5.6 language and decided to move CMA to a new Section 5.9.

The task group is working to clean up the document and make it more consistent with what’s been approved so far, he said. Later in the meeting, the subcommittee passed a motion to move NFRC 100 Section 5.9 to the Technical Committee for approval.

Complex Products Ballot Delayed
The subcommittee then focused on the CMA Complex Products – NFRC 100, Section 5.9.6 ballot. The ballot involved the development of a rating procedure for all complex products.

The subcommittee discussed the first negative, from Birch Point Consulting, LLC. Its negative said that corner products should be removed, due to the level of complexity it would add to the CMA at such an early stage of the program. The subcommittee passed a motion finding the negative comment to be persuasive and substantive.

Next, the group discussed Pella/EFCO’s recommendation to shelve this ballot for at least one year to allow the industry to focus on getting CMA up and running with simple product configurations. The negative comment went on to state that after “CMA is established...we can regroup and draw on a year's experience with CMAST to determine how best to tackle complex products.” The subcommittee passed a motion finding the comment to be persuasive and substantive.

NNN's Global Reach

After Peter Lyons mentioned that some of his colleagues are following the Fall Membership Meeting through NFRC News Now (NNN), we decided to check Google to see if people in any other countries are checking in.

They are! As of Tuesday, visitors had come to NNN this week from 10 countries outside the United States:
  • Australia
  • Canada
  • Denmark
  • Italy
  • Mexico
  • Slovakia
  • South Africa
  • Spain
  • Switzerland
  • United Kingdom

The power of the World Wide Web!

SHGC Subcommittee Addresses Several Ballots

The Solar Heat Gain Coefficient Subcommittee convened Wednesday morning under the leadership of Vice Chair Bipin Shah, WinBuild, Inc., and addressed several ballots.

First up was the NFRC 200 Dynamic Attachments for Swinging Doors ballot, which received no negatives or approvals with comment and which was approved and moved forward to the Technical Committee for approval into the 200-2004 and 200-2010 documents, with implementation upon publication.

After disposing of several negatives and approvals with comment, the subcommittee next approved the NFRC 200 Applied Film Ballot and moved it forward to Technical Committee for approval into the 200-2010 document, with implementation upon publication.

The NFRC 200 WINDOW6/THERM6 Software ballot did not fare so well, as multiple negatives were ruled persuasive and the subcommittee voted to return the document to task group for further review. The group did the same with the NFRC 200 Garage Door Ballot.

Subcommittee Reaffirms NFRC 200, 201 for 2010
As its final actions, the subcommittee reaffirmed the NFRC 200-2004 and NFRC 201-2004 documents with approved changes as NFRC 200-2010 and NFRC 201-2010, and forwarded them to the Technical Committee for approval, with implementation upon publication and direction to sunset the 2004 documents at the same time.

U-Factor SC Passes Motions, Forms Task Group

The third day of the NFRC Fall Membership Meeting got underway with the U-Factor Subcommittee passing a handful of motions.

After the subcommittee’s chair, Michael Thoman of Architectural Testing, Inc., opened the subcommittee meeting, attendees heard reports from task groups, including updates from the Garage Rolling/Door Task Group and the Door Task Group.

Joe Hetzel of DASMA reported on the Garage/Rolling Door Task Group, noting progress is being made on the research project and that it’s in its final phase. He said the task group may look into presenting a ballot in the future about developing a standardized spreadsheet for simulation of rolling doors and garage doors.

Dave DeBlock of ODL Incorporated updated the subcommittee on the Door Task Group’s activities. He reported that the task group efforts to try to coordinate simulation for doors, including looking to create a universal spreadsheet for simulators.

The subcommittee then turned it attention to ballots. It passed several motions, including:

· To forward the NFRC 100 Garage/Rolling Door ballot to the Technical Committee for approval into the NFRC 100-2010 document with implementation upon publication.

· To forward the NFRC 100 Dynamic Attachments for Swinging Doors (DASD) ballot to the Technical Committee for approval into the NFRC 100-2004 document and NFRC 100-2010 document with implementation upon publication.

· To find the negative comment from Architectural Testing, Inc., on the NFRC 100 Window 6/THERM 6 Software ballot (i.e., can’t approve without having the results of the Window 6/THERM 6 project) to be persuasive.

· To find the negative comment on section 4.3.1.C.ii in the NFRC 100 Window 6/THERM 6 Software ballot to be persuasive and return the ballot to task group.

· To move forward the NFRC 100 Validation Matrix ballot to the Technical Committee for approval into the NFRC 100-2010 document with implementation upon publication.

· To approve the NFRC 102-2010 ballot and move forward for publication.

· To find the one “approved with comment” on the NFRC 100-2010 ballot to be non-persuasive and change the ¼ lite size designation to include everything up to but less than 410 sq. in.

· To move the NFRC 100-2010 ballot to the Technical Committee for approval with implementation upon publication.

The subcommittee then reviewed negative comments to the NFRC 100 Applied Films ballot, and after finding them to be non-persuasive, passed a motion to move forward the NFRC 100 Applied Films ballot to the Technical Committee for approval into the NFRC 100-2010 document with implementation upon publication.

New Task Group Will Look at Test Sizes
The subcommittee concluded its business by forming a new task group, to be chaired by Mike Manteghi of TRACO, to focus primarily on testing sizes for casement windows and awnings. Some members expressed concern that the way these products are currently tested provides misleading ratings to consumers who compare different product types such as double-hung and casement.

Technical Committee Reconvenes

We're back up and running on Wednesday morning, with the U-Factor Subcommittee, chaired by Mike Thoman of ATI, leading us off.

Tuesday, November 17, 2009

AEP: Could It Be True?

After nearly 20 years of development, an NFRC subcommittee has approved an annual energy performance procedure. At 9:06 p.m. Central Standard Time, by unanimous voice vote, the AEP Subcommittee, chaired by Jim Larsen (with an "e") of Cardinal Glass Corporation, sent NFRC 901 to the Technical Committee for review.

And with that, the NFRC meeting mercifully came to a close. The Technical Committee will reconvene at 7:30 on Wednesday morning.

Air Leakage Subcommittee Continues Evening Session

NFRC continued to burn the midnight oil as the Air Leakage Subcommittee focused on its business this evening.

Michael Thoman of Architectural Testing, Inc., chair of the subcommittee, opened the meeting, followed by a report from Chris Nolt of ProVia Door, Inc., on the Air Leakage Task Group’s activities.

The subcommittee then turned its attention to the NFRC 400-2010 ballot review, which drew four negatives and two approved with comments.

Several motions were presented and approved by the subcommittee. It passed a motion that found Andersen Corporation’s first negative comment on the ballot persuasive and substantive, sending it take back to Task Group to revise the language. The subcommittee addressed Andersen’s second comment, regarding how reporting differences are to be reconciled, by passing a motion to find the negative substantive and persuasive and allow the report to follow the NAFS requirements if following the NAFS test method and follow NFRC 400 requirements if following the NFRC test method.

After the ballot’s third negative comment was withdrawn, the subcommittee voted on its third motion of the evening: to find VELUX’s negative persuasive and substantive and include language to allow the manufacturer to supply the largest production size if it is less than the minimum size of the NAFS table.

The subcommittee meeting concluded after it passed a motion to reaffirm NFRC 400-2004 as an interim document.

Results from the Attachments SC Straw Polls

Results from the non-binding base case window straw polls taken after the Attachments Subcommittee reconvened for a rare late-night session are available on the Attachments Subcommittee page on the NFRC Web site.

Attendees Take Break from NFRC Business

After two busy days of program business, attendees took a well deserved break at the NFRC's 20th Anniversary Membership Reception this evening. The event featured authentic Tex-Mex cuisine, a mariachi band, and a champagne toast to celebrate NFRC's special milestone.












Attachment SC Meeting to Reconvene Tonight

Members of the Attachment Subcommittee engaged in a spirited debate over the base case window products included in NFRC 100-A (or, possibly, NFRC 104, but more on that later).

With some members arguing that the time had come to move forward and others cautioning that the approach NFRC takes has to ensure a level playing field and deliver information that customers for attachment ratings need and want, the group ultimately decided to withdraw the ballot and conduct a series of straw votes to provide the task group with better direction on the issue.

But not before the subcommittee decided to break for the NFRC Membership Reception. The subcommittee will reconvene at 7:30 this evening.

Wish You Were Here?

NFRC served up a field of colorful cupcakes for the Tuesday afternoon break. Delicious!

W6/T6, CMAST Approval Task Groups Report Progress

The Technical Committee Block got underway with two reports from the Software Subcommittee, one from the WINDOW 6/THERM 6 Approval Task Group and another from the CMAST Approval Task Group. Both groups are making progress on their respective tasks.

Joe Hayden of Pella reported that the W6/T6 Approval Task Group is managing the process of obtaining NFRC approval of W6/T6 per NFRC Software Approval Guidelines. About 80 percent of the work under the approval process is complete, including the cost-benefit analysis. The task group’s goal is to obtain approval of W6/T6 at the NFRC 2010 Spring Membership Meeting in New Orleans.

The committee then heard the latest on the CMAST Approval Task Group’s work. Jessica Ferris, NFRC’s CMA program manager, reported that the only outstanding task from the Summer Membership Meeting was the verification study. Since that meeting, the task group completed that task, and NFRC posted the report to its Web site and announced its availability to the membership for review. (Members had two weeks to review the report.) At its September meeting, the Board of Director reviewed the members’ comments, and then approved CMAST for the pilot program, along with W6/T6. The Board also moved forward to approve CMAST for the full implementation of CMA in January 2010.

Optical Properties SC Hears Task Group Reports

The Optical Properties Subcommittee met Tuesday morning and heard reports from several task group chairs.

Ray McGowan, NFRC’s senior research and technology manager, encouraged members to get involved with the NFRC 302 Task Group “because the whole document is being reviewed and there could be significant changes.”

Charlie Curcija of Carli, Inc. told the subcommittee that the Non-planar Simulation Task Group is working on a one-page research summary page and plans to submit it at the next meeting.

The subcommittee also heard reports from the Attachment Optical Properties Task Group and a brief update on ISO activity.

Research SC Approves Numerous Motions

The Research Subcommittee, chaired by Bipin Shah of WinBuild, Inc., approved five motions during its Tuesday morning meeting. These approvals included motions by:

- Kevin Vilhauer of Milgard Manufacturing, seconded by Dave De Block of ODL Incorporated, to extend the completion date for the Condensation Resistance Procedure for CMA research project to January 31, 2010;

- Joe Hayden of Pella Corporation, seconded by Charlie Curcija of Carli, Inc., to extend the completion date for the WINDOW 6/THERM 6 Validation research project to the Spring 2010 membership meeting;

- Hayden, seconded by Steve Harp of Associated Materials, Inc., to recommend to the Research & Technology Committee that it approve a $5,200 increase in funding for the WINDOW 6/THERM 6 project;

- Sneh Kumar of TRACO, seconded by Tracy Rogers of Edgetech I.G., to recommend to the Research & Technology Committee that it approve a “CMA methodology” summary page for RFP development; and

- Peter Lyons of Peter Lyons & Associates, seconded by Roland Temple of AZS Consulting, to recommend to the Research & Technology Committee that it approve a “spandrel system performance validation” summary page for RFP development.

Research Funding Is Available
NFRC Senior Research and Technology Manager Ray McGowan told the subcommittee that approximately $1.1 million is available to fund research projects through 2014 (though three proposed projects would use up approximately $250,000 of that amount, if approved).

“There are funds available, and I encourage members to submit summary sheets,” McGowan said.

Thoughts Shared on Improved Project Management
John Gant of Glen Raven presented four ideas, developed by the NFRC 703-Research Program Manual Task Group, intended to minimize delays and cancellations and prevent negligent behaviors by all participants. Subcommittee members discussed the possibility of:

- including more regimented delivery dates in contracts, with payments tied into those dates;
- imposing financial penalties for late deliverables that are not justified;
- retaining a portion of projects’ budgets until entire the projects are complete; and
- assigning greater responsibility for PMTGs to meet frequently and respond and manage the process and communicate issues.

Also during the Research Subcommittee meeting, Ross McCluney presented reports on the Complex VT Rating and Attached Awning Ratings research projects.

Research & Technology Committee Passes Four Motions

After Chair Werner Lichtenberger of TruSeal Technologies welcomed members of the Research and Technology Committee, the group wrapped up the morning’s business by passing four motions presented by its subcommittees.

Bipin Shah of WinBuild, Inc., who chairs the Research Subcommittee, presented three motions to the committee to:

·Extend the Window 6/Therm 6 Validation research project deadline to NFRC Spring 2010 Membership Meeting
·Extend the deadline for the Condensation Resistance for the Component Modeling Approach (CMA) project to January 31, 2010
·Increase funding by $5,200 for the Window 6/THERM 6 Validation research project

He also noted that the Research Subcommittee appointed Peter Lyons of Peter Lyons & Associates as its vice chair after Rich Biscoe of Architectural Testing, Inc., resigned. Shah welcomed Lyons to the position and thanked Biscoe “for all the support he’s given us.” Bipin also mentioned that the subcommittee is seeking a task group chair for long-term research activities.
Sneh Kumar of TRACO Inc., who serves as the chair of the Optical Properties Subcommittee, reported that his committee had no motions to present. He requested that more NFRC members participate in the subcommittee’s activities.

Charlie Curcija of CARLI, Inc., who chairs the Thermophysical Properties of Materials Subcommittee brought forward the fourth motion to the subcommittee:

·To move NFRC 101 forward to the Board of Directors, except for items sent back to the Task Group, with implementation upon publication of the 2010 documents.

Curcija, who also chairs the Glossary and Terminology Subcommittee, noted it had no action items for the subcommittee.

With the passage of the motions, the Research & Technology Committee moved these actions items to the Board for final approval.

CMA/Title 24 Brochure Available in Registration Area

Meeting attendees are encouraged to pick up a copy of the Component Modeling Approach (CMA) brochure focusing on the new provision in California’s Title 24 2008 energy standards for site-built fenestration in non-residential buildings. It is available in the registration area outside the Crystal Ballroom.

The brochure outlines the CMA process and provides information on using CMA for Title 24 energy compliance. An insert provides additional details on the:

·CMA Software Tool (CMAST)
·CMA Label Certificate
·Certificate of Compliance (ENV-1C)
·Certificate of Acceptance (ENV-2A)
·Acceptance Requirements (NA7.4.1)

A sample CMA Label Certificate is also included.

NFRC is offering education opportunities that focus on CMA and Title 24. On December 3, 2009, and January 28, 2010, NFRC will present a free educational webinar designed for building officials and energy consultants in California, conducted by the Heschong Mahone Group. More information is available online.

Meeting Presentations Available on the Web

If you would like to review the presentations given during the meetings that took place on Monday, Nov. 16, NFRC staff has uploaded them to the NFRC Web site.

Glossary TG Reviews 600 Ballot

After briefly discussing ways to improve the navigability of NFRC’s ever-growing glossary of terms, Chair Charlie Curcija steered the Glossary and Terminology Task Group through discussion of numerous negatives and approvals with comment on the NFRC 600-Glossary and Terminology Ballot.

The group found two negatives, submitted by Joe Hayden of Pella Corporation and Jim Larsen of Cardinal respectively, to be persuasive.

On a unanimous voice vote, the group approved a motion – made by Hayden and seconded by Steve Johnson of Andersen Corporation – to find Hayden’s negative to be editorial and substantive. As a result of this motion, NFRC 600 will need to be re-balloted.

By a vote of 18-7, the group approved the following motion – made by Les Condit of Entech Solar and seconded by Sneh Kumar of TRACO – in response to Larsen’s negative:

"Definitions remain in NFRC 600 and be added into their respective documents. Staff will inform membership if specific document definitions and NFRC 600 do not match or if any new definition conflicts with existing definitions."
Check Spelling
“We will take these negatives into account, and come back with a new ballot,” Curcija said, closing the meeting.